603-225-2779 x 254 email us
Bogie wheel brackets
Track idler wheel kits
Body fastener kits
Carburetors and parts
Fuel system parts
Clutches and parts
Exhaust sealing kits
Front leaf springs
Heated handlebar grips
Kick starter parts
Oil tank caps
Pistons & rings
Ski wear bars
Track drive gears
Track drive shafts
Track sliders (hyfax)
Winter service kits
|AIR FILTERS - $17.99
We stock OEM Sno-scoot foam air filters. The Yamaha part number for this item is 85G-14451-00-00 and it is a stock replacement part for all 1988-1990 years of the Sno-scoot.
|BRAKE LEVERS - $13.99
We stock OEM Sno-scoot brake levers. The Yamaha part number for this item is 8H8-83912-00-00 and it is a stock replacement for all 1988-1990 years of the Sno-scoot.
|CARBURETOR REBUILD KITS - $68.99
We stock carburetor rebuild kits for 1988-1990 year Sno-scoots. The kit includes a new main jet, pilot jet, needle valve (float valve), two float bowl gaskets that replace the stock discontinued Yamaha gasket (two gaskets are stacked under the carb bowl) and the two ever-important rubber caps. This kit replaces all the common parts to wear out on your carb and is simple to install. We have even put together instructions for those of you who have not rebuilt a Sno-scoot carb before.
Click HERE to see our detailed instructions.
|FUEL FILTERS - $19.99
We stock original equipment Sno-scoot in-tank fuel filters. The Yamaha part number for this item is 85G-24560-00-00 and it is a stock replacement part for all 1988-1990 years of the Sno-scoot.
|OIL INLET T-FITTING - $10.99
We stock genuine Yamaha oil inlet T-fittings for all 1988-1990 years of the Sno-scoot. The Yamaha part number for this fitting is 815-24379-00-00 and it is the original Yamaha part that came on these machines.
|FUEL PUMPS - $89.99
We stock OEM Yamaha (Keihin) Sno-scoot fuel pumps. The Yamaha part number for this fuel pump assembly is is 8R4-24410-01-00 and it is a stock replacement part for all 1988-1990 years of the Sno-scoot.
|PRIMARY CLUTCH SHEAVE REPLACEMENT KIT - $230
We stock primary clutch replacement kits for all 1988-1990 years of the Sno-scoot. The original Sno-scoot sliding primary clutch sheave, Yamaha part number 85G-17601-00-00, has been discontinued, but we have developed a kit that is a bolt in replacement. This kit includes a new custom machined sliding clutch assembly with six weights (install just three to get a snappy launch), a new sliding sheave bushing, and a new backspacing bushing (not shown). If your machine is equipped with electric start, please read the note below.
Click HERE to see our detailed installation instructions.
ATTENTION ELECTRIC START SNO-SCOOT OWNERS:
|DRIVE BELTS - $34.99
We stock OEM Sno-scoot drive belts. The Yamaha part number for this item is 32N-17641-00-00 and it is a stock replacement for all 1988-1990 years of the Sno-scoot.
|HEADLIGHT DIMMER SWITCHES - $24.99
We stock quality aftermarket Sno-scoot headlight dimmer switches. They are priced about $10 less than the Yamaha switch and they are an exact copy. This switch fits all 1988-1990 years of the Sno-scoot.
|SPARK PLUGS - $4.99
We stock NGK BR8HS spark plugs, which is the stock plug for all 1988-1990 Sno-scoots. These are always good to have on the shelf if you own a scoot.
|TAILLIGHTS - $44.99
We stock OEM Sno-scoot taillight assemblies. The Yamaha part number for this item is 85G-84710-00-00 and it is a stock replacement part for all 1988-1990 years of the Sno-scoot.
|HEADLIGHT BULBS - $7.99
We stock OEM Sno-scoot headlight bulbs. The Yamaha part number for this item is 8A7-84314-00-XX and it is a stock replacement part for all 1988-1990 years of the Sno-scoot.
|SCOTTS HANDLEBAR GRIPS - $12.99
We stock Scott brand grips. These grips are sold in pairs and are available in black.
|KICK STARTER GEAR RETURN SPRING - $14.99
We stock Sno-scoot kick starter lever return springs. The part number for this item is 90508-32609-00 and it is a stock replacement part for all 1988-1990 years of the Sno-scoot.
|OIL TANK CAPS - $14.99
We stock OEM Sno-scoot oil tank caps. The Yamaha part number for this cap is 1Y1-21770-01-00 and it is a stock replacement part for 1988-1990 Sno-scoots.
|REED CAGE GASKET - $4.99
We stock replacement reed cage gaskets for 1988-1990 Yamaha Sno-scoots. This gasket is a duplicate of the now discontinued Yamaha gasket, part number 88W-13621-00-00.
|CRANKSHAFT REBUILD PARTS
We offer crank-shaft rebuild parts for 1988-1990 Sno-scoots. We offer bearings, connecting rods, and crank pins. We also offer a full kit that includes everything shown to the left. Please be aware the replacement of the connecting rod and lower rod bearing require a skilled engine machine shop for disassembly and reassembly of the crank (parts press together and have to be aligned properly). Select the parts that you need in the drop down menu below.
We stock the bearings and crank pin, but the connecting rod is a special-order item that typically ships about 5 business days after purchase.
|BOYESEN POWER REEDS - $34.99
We stock Boyesen Power Reeds for 1988-1990 stock Sno-scoot reed cages. These parts bolt right up and add to the performance of your machine.
|VFORCE 3 REED VALVES - $204.99
We offer Moto Tassinari VForce III reed valves for Sno-scoots. These reed valves are the ultimate in intake performance. Carbon fiber reeds and a high capacity reed cage add snap to your throttle response. This kit fits all 1988-1990 years of the Sno-scoot. This kit typically ships in 2-3 business days.
|SEAT COVERS - $69.99
We stock black and red reproduction seat covers for all 1988-1990 years of the Sno-scoot. These covers fit just like the stock ones and are made just for us by a well known seat cover manufacturer. These covers have the Yamaha insignia just like the stock covers.
Seat covers are currently out of stock. We will offer them again when more arrive from the supplier.
|SEAT PANS - $139.99
Snoscoot.com now stocks replacement seat pans for 1988-1990 Yamaha Sno-scoots! Lots of Sno-scoot riders asked for replacement seat pans, so we made it happen. These pans are made from a durable HDPE plastic that is form fitting to the Sno-scoot and based on the original Yamaha base pan, which was never offered by Yamaha separately from the whole seat assembly.
Our seat pans come as a kit and require use of your factory seat latch. If your seat latch is no longer usable, we will have those listed on this page shortly. These pans are EXCELLENT quality, but as they are hand made, and Sno-scoot frames are rarely perfectly straight, they do require fitting and adjusting before installing your foam and cover (sold separately). This kit comes with the pan itself, required mounting hardware, stainless steel locator pins, and rubber bumpers. What this means is that each pan will require individual fitment to your frame, so when you receive it, you will have to drill the 1/2", 1/4", and 3/16" holes required to mount the locator pins, rubber bumpers, and seat latch. We also provide enough spacers for the latch to fine tune the fit before you install your foam and seat cover. To guide you through this simple process, we have put together a full set of assembly and mounting instuctions. Click HERE to see the instructions.
|SEAT LATCHES - $34.99
Snoscoot.com now stocks replacement seat latch assemblies for all 1988-1990 years of the Sno-scoot. These latches are brand new genuine Yamaha parts and require assembly.
|SEAT FOAM - $169.99
We now stock replacement seat foam for 1988-1990 Yamaha Sno-scoots! Yamaha never offered the foam separate from the rest of the assembly (when it was available from Yamaha), so we have this foam made just for us right here in the US. This foam is a time tested polyurethane material that is molded to the original shape and is slightly higher density than the original seat.
|OEM STEEL SKIS - $84.99 EACH
We stock OEM Sno-scoot steel skis. We sell these skis individually, so if you need two, you need to order a quantity of 2. The Yamaha part number for this ski is 85X-23710-00-00 and it is a stock replacement part for all 1988-1990 years of the Sno-scoot.
|C&A PLASTIC SKIS & CARBIDES - $494.99
Snoscoot.com stocks C&A plastic ski kits for Yamaha Sno-scoots. These kits come with a pair of modified black C&A plastic mini skis, pair of 6" 90° angled carbide ski wear bars, pair of durable fabricated aluminum ski brackets (weigh only 11.5 oz. each), and the required mounting hardware. This kit makes use of your original ski pivot bolts, but requires replacement of your original pivot bolt nuts, which are included with this kit. Some bolt-together assembly is required with this kit, but no modification to your Sno-scoot is required. This kit fits all 1988-1990 years of the Sno-scoot.
|SNOSCOOT.COM C&A MINI SKI MOUNTING KITS - $210.99
We stock mounting bracket kits for C&A mini skis. If you already have a pair of skis, our kit is exactly what you need to bolt them onto your Sno-scoot. Our kit comes with the same high-quality fabricated aluminum mounting brackets (weigh only 11.5 oz. each) and hardware that we use on our complete C&A mini ski kit above. The brackets themselves make use of two of the ski wear mounting studs and nuts, and you will use your existing ski pivot bolts (replacement nuts is included - replacement nuts and bolt listed below). Please be aware that you will have to trim about 3/8" off the tops of the ski mounting flanges, as we do with our complete kit above. This kit DOES NOT include skis or wear bars. This kit fits all 1988-1990 years of the Sno-scoot.
|SKI PIVOT BOLTS & NUTS - $18.99/SET
We stock stainless steel ski mounting nut and bolt sets for Sno-scoots. The original ski pivot bolts, Yamaha part number 90102-08071-00, have been discontinued, so we sourced this stainless hardware. Our kit comes with two bolts and two nuts, so it includes new mounting hardware for both skis on your machine. This hardware kit fits all 1988-1990 years of the Sno-scoot.
|SKI SKINS - $119.99/SET
SNO-SCOOT SKI SKINS ARE BACK! Made just for snoscoot.com by a US based plastics manufacturer, they are specifically molded for 1988-1990 Sno-scoot (and Sno-sport) skis. These skins are made out of super durable 1/8" HDPE plastic and they fit just right! To keep the price down, you do have to drill the holes to mount them, but that's easy to do. The holes you need to drill are as follows.
HOLES TO DRILL:
For further mounting instructions, please give us a call. Our ski skins are sold in pairs and include the mounting hardware for the front, as well as washers for the ski wear bars. The ski and wear bar shown installed in the bottom three pictures to the left are NOT included.
|STEEL SKI WEAR BARS - $19.99
We stock quality aftermarket Sno-scoot steel ski wear bars for all stock 1988-1990 Sno-scoot skis. These bars are sold in pairs, so if you need enough for one Sno-scoot, order a quantity of 1. These bars come with mounting nuts.
|CARBIDE SKI WEAR BARS - $89.99
We stock high-end Yamaha Sno-scoot carbide ski wear bars. Specially made for Snoscoot.com by a well known snowmobile skag manufacture here in the US, these 1/2" diameter heavy-duty steel bars come with 4" of 60° carbide in the center, 5" of hardweld bead in the front, and 6.5" of hardweld bead in the back for solid bite and a long lasting bar. When installing these bars, please be aware that the second wear bar mounting dimple on the rear of each ski needs to be drilled out and the stock mounting holes, including the front hole, need to be oversized to fit the bar. These bars fit all stock 1988-1990 Sno-scoot skis and are sold in pairs, so if you need enough for one machine, order a quantity of one.
|THROTTLE LEVERS - $28.99
We stock OEM Sno-scoot throttle levers. The Yamaha part number for this item is 8V0-42138-00-00 and it is a stock replacement part for all 1988-1990 years of the Sno-scoot.
|TRACKS - $459/$549
Sno-scoot 80 tracks are back in stock! Yamaha discontinued the original part and we have sold all the genuine Yamaha Sno-scoot tracks that will EVER be made. However, do not fear! We stepped up to the plate and worked with a track manufacturer to make these tracks for us. After 11 months of development time and multiple test tracks, we have come up with a durable design that fits perfectly and has passed our torture tests. WE ARE NOW ALSO SELLING LONG TRACKS FOR THE SNO-SCOOT and proper length tracks for Sno-sports (listed on the Sno-sport Common Parts page - $499). The "long" tracks will have another 6 sets of windows over the stock Sno-scoot design, so they will put another 12" of track on the ground, while the stock length tracks bolt up right up withouth any modification. We are even selling these tracks for a fair amount less than what we last offered the Yamaha track for! These tracks fit all 1988-1990 year Sno-scoots.
+12" "long tracks" DO NOT include parts or instructions to lengthen your rear suspension skid, but is just the track, which is the most difficult part to source (works with stock track drive cogs).
OUR TRACKS HAVE ARRIVED AND ARE NOW READY TO SHIP!
Click HERE to see our detailed removal and installation instructions.
|TRACK CLIPS - $24.90/10 PACK
We stock quality aftermarket track clips for 1988-1990 Sno-scoots. These clips are duplicates of the OEM clips, which Yamaha calls track reinforcement plates. They will fit stock and our replacement tracks and they are priced less then the OEM part. We sell these clips in packs of 10 and they fit all original Sno-scoot tracks. Please be aware that the design of our clips is a little different than the early Sno-scoot tracks (similar to the last run of Sno-scoot tracks we received from Yamaha).
|TRACK STUD KITS - $68.99/$137.99
We offer carbide track stud kits for 1988-1990 Yamaha Sno-scoots. These kits come with appropriately sized 3/4" long 60° carbide tipped studs, mounting nuts, and aluminum backing plates in kits of 20 or 40 so you can get some serious traction. The included studs are just long enough to add traction but not tear up the track guard, unless that part is broken and dangling, in which case these studs will shread it to bits! To the left, we have provided a couple diagrams showing how we recommend installing the two kits.
If you're looking for serious bite, add a pair of the Snoscoot.com carbide ski wear bars or our C&A plastic ski kit (listed above) to your order and your Scoot will feel like it's on rails!
This kit typically ships in 2-3 business days.
|TRACK COVERS / SNOW FLAPS - $124.99
Snoscoot.com now stocks mini-tunnel style track covers for Sno-scoots. The original Yamaha snowflap that always breaks, part number 85G-77564-00-00, has been discontinued, so we now offer these trick track covers fabricated out of 0.080" thick aluminum sheet. This part mounts to the frame itself and looks sharp on any Scoot! To keep pricing down, this part comes in bare aluminunm and includes four simple screw-type mounting clamps. This tunnel kit fits all 1988-1990 years of the Sno-scoot.
When mounting kit, you will want to remove the plastic body panel and unbolt the lower shock mount. This will allow you to swing the track down out of the way to install the mouting clamps.
|TRACK DRIVE GEAR - $139.99
We offer stock Yamaha Sno-scoot track drive gears. This is the gear that the front track drive axle inserts into and has splines on the inside of the backside and comes with a needle bearing assembly pressed into the front side. The Yamaha part number for this gear is 85G-17420-00-00 and it fits all 1988-1990 years of the Sno-scoot. This part typically ships in about 5 business days.
|TRACK DRIVE SHAFTS - $264.99
Snoscoot.com has 1988-1990 Sno-scoot track drive shafts in stock! After searching for YEARS for a machine shop to make track drive shafts to replace the discontinued Yamaha shaft, part number 85G-47511-00-00, we now have stock replacement shafts on hand. These beautifully machined shafts are made by Chinook Fabrication and Design in Ontario, and they are exact duplicates of the stock Yamaha drive shaft. Two solid seasons of testing went into these shafts and they fit perfectly. The shaft makes use of the stock bearings and retaining nut.
|TRACK DRIVE SHAFT BEARINGS - $22.49
Snoscoot.com stocks factory original Yamaha track drive shaft bearings for all 1988-1990 years of the Sno-scoot. This is the bearing that goes on the right side of the frame just to the left of the disk brake and supports the right side of the track drive shaft. The Yamaha part number for this bearing is 93306-00444-00, which replaces part number 93306-00441-00, and it is a stock replacement for all 1988-1990 Sno-scoots.
|TRACK DRIVE SPROCKETS -
We have track drive sprockets in stock for 1988-1990 Sno-scoots! The original Yamaha sprocket, part number 85G-W4753-02-00, was discontinued back in 2015, but after a couple years of hunting, we finally have a replacement! Our track sprockets are machined from a super durable HDPE plastic and press onto the stock Yamaha drive shaft, or the aftermarket track drive shaft that we stock. As these sprockets are slightly different than the stock drive cog, we only sell them in pairs.
We have quite a few of these sprockets on hand, so we're offering a great deal to get some shelf space back!
|TRACK SLIDERS - $29.99/SET
We stock OEM Sno-scoot track sliders, also known as hyfax. We sell these as a set of two, so if you need a pair for a single machine, order a quantity of one. The Yamaha part number for each track slider is 85G-47421-00-XX and this is a stock replacement hyfax set for all 1988-1990 years of the Sno-scoot.
|TRACK SWINGARM PIVOT BEARINGS - $16.99 each
Snoscoot.com stocks factory original Yamaha track swingarm pivot bearings for all 1988-1990 Sno-scoots. The Yamaha part number for this bearing is 93306-00316-00 and we sell them individually, so if you need both for your machine, please order a quantity of two here. We have pointed out the location on these bearings on the diagram to the left.
|TIEROD ENDS - $29.99
We stock OEM tierod ends for Yamaha Sno-scoots. The part number for each inner tierod end (steering stem end) is 86X-23841-00-00 and the part number for each outer tierod end (ski spindle end) is 86X-23845-00-00. For reference, the inner rod end has a right hand thread (part that threads into connecting tie rod tube) and the outer rod end has a left hand thread. These ball joints are stock replacement parts for all 1988-1990 years of the Sno-scoot.
|WINDSHIELDS - $159.99
We stock quality aftermarket PowerMadd windshields for Yamaha Sno-scoots. These shields provide great coverage keeping you a bit warmer when riding. The shield itself is clear with accent tinting at the bottom and comes with the required mounting hardware. This kit bolts up to all 1988-1990 years of the Sno-scoot.
|WINTER SERVICE KITS - $75.99
We stock Sno-scoot winter tune-up kits. The kit consists of a new OEM drive belt, air filter, in-tank fuel filter, and spark plug. This kit is for all 1988-1990 years of the Sno-scoot.